What is the lug nut torque for a 2011 subaru forester?

Service manual says 88.5 ft-lbs. via

What should Subaru wheels be torqued to?

2020 Subaru Models Wheel Lug Nut Torque Specs Table

2020 Subaru Models Engine Wheel Lug Nut Torque Specs lb-ft (Imperial)
IMPREZA ALL F4-2.0L DOHC 88.5 lb-ft
LEGACY All Engines 88.5 lb-ft
OUTBACK All Engines 88.5 lb-ft
WRX ALL All Engines 88.5 lb-ft

via

What is lug nut torque?

Under- or over-tightening wheel-attaching hardware can be damaging and dangerous.

Hardware Bolt or Stud Size Typical Torque Range in Ft/Lbs Minimum Number of Turns of Hardware Engagement
14 x 1.5 mm 85 - 90 7.5
14 x 1.25 mm 85 - 90 9
7/16 in. 70 - 80 9
1/2 in. 75 - 85 8

via

What size are Subaru Forester lug nuts?

M12x1. 25 Open End Bulge Acorn Lug Nut - 19mm Hex - 60 Degree Cone Seat. via

What happens if you over torque lug nuts?

When you over-torque the lug nut you could cause stress fractures and this makes it no longer certified for the load rating, there is a risk of the lugs breaking under normal conditions and your wheels will pass you in traffic, rare, but it does create a safety concern. via

What size lug nuts are on a 2015 Subaru Forester?

Subaru Forester 2015, Cone Seat Acorn Lug Nuts by Gorilla Automotive®. Thread Size: M12 x 1.25. Hex Size: 13/16". Overall Length: 35.56 mm. via

What is the lug nut torque on a 2010 Subaru Outback?

Subaru Lug Nut Torque Specs Recommendations

Model Trim Torque
OUTBACK 2.5I 16"BASE / BASE 90 lb-ft
OUTBACK 2.5XT 17"BASE / LIMITED 90 lb-ft
OUTBACK 3.0R 17"BASE / LIMITED 90 lb-ft
OUTBACK 3.6R 17"BASE / ALL 90 lb-ft

via

How many foot pounds do you need to tighten lug nuts?

And when you look at that, and realize that the average torque required on a lug nut, to hold the wheel on, is 80 to 90 ft-lbs, well you can imagine how over-tightened some of these lug nuts are. Now that's a problem because it almost guarantees warped brake rotors. via

How do I find the torque specs for my car?

The torque specs for the axle nut (and other nuts and bolts) should be listed in the dealership/shop guide provided by the manufacturer. If you can't find that information, or if you don't have a guide, you can find the specs in the service manual. via

Should you tighten lug nuts after new tires?

Lug nuts must be torqued to the manufacturer's recommended values, and they must be re-torqued to those values after driving approximately 50 to 100 miles on your new tires after the tire service. Both under and over tightening can be dangerous. via

How tight should wheel nuts be?

Step 3: Install the nuts by hand.

Most manufacturers do not recommend using any lubricant or anti seize compound on the lugs. Push the wheel home on the hub and using your socket wrench, tighten the wheel nuts just enough to hold the wheel snugly. via

Do I need to re torque my wheels?

Whenever you have new wheels and tires fitted to your car – for example, you've done the sensible thing and switched between summer and winter tires – it's essential to have the lug nuts retorqued after the first 50 kilometers. Why should a responsible driver do this? The point is road safety. via

Are all Subaru lug nuts the same?

None of this is specific to Subaru. All cars should have the wheel lug nuts torqued. What is specific to Subaru is the 1.25 thread pitch. If the same torque is applied to a 1.25 pitch fastener and a 1.5 pitch fastener, the 1.25 will be tighter, that is, it will have higher clamping force. via

What size are Subaru Outback lug nuts?

Dorman - Autograde - Wheel Nut M12-1.25 Standard - 19mm Hex, 16mm Length (sold by each) (Part No. 611-064) via

What size lug nuts are on a 2008 Subaru Outback?

Subaru Outback 2008, Cone Seat Flattop Capped Lug Nuts by Dorman®. Thread Size: M12 x 1.25. Hex Size: 19 mm. Overall Length: 1.807". via

Is it OK to hand tighten lug nuts?

Can you over-tighten your lug nuts by hand? Sure you can. If it's not just your car that's jacked up. If you have the necessary muscle, you could tighten the nuts more than the specifications call for. via

Can you over tighten lug nuts with a tire iron?

Excessively tightened lug nuts can strip the threads, distort brake rotors, damage the wheel, and possibly shear off the lug stud. Insufficiently tightened lug nuts can come loose, with catastrophic consequences. via

Can over tightening lug nuts warped rotors?

Over-torquing a wheel can result in a warped brake rotor and possible hub flange damage. Rotors get extremely hot and improper, and over-torquing a wheel can result in warpage as the rotor heats up and cools back down in service. via

What size is the lug nut for 2019 Subaru Forester?

M12x1. 25 Open End Bulge Acorn Lug Nut - 19mm Hex - 60 Degree Cone Seat. via

What size lug nuts are on a 2010 Subaru Outback?

Subaru Outback 2010, Chrome Cone Seat Acorn Bulge Lug Nuts by Dorman®. Thread Size: M12 x 1.25. Hex Size: 13/16". via

What size is a Subaru lug nut?

Dorman - Autograde - Wheel Nut M12-1.25 Standard - 19mm Hex, 16mm Length (sold by each) (Part No. 611-064) via

What is the lug nut torque on a 2016 Subaru Outback?

The manual says 89 lb-ft. via

Is 300 ft lbs enough to remove lug nuts?

Realistically, the answer is no. A quick glance at a lug nut torque chart shows that most lug nuts should be torqued between 80 and 100 ft-lbs. Some require less torque, others more. via

Can you use impact driver for lug nuts?

Can an Impact Driver Remove Lug Nuts? Yes, technically. You would need to use a hex shaft to square drive adapter in order to attach a lug nut socket to the tool. However, an impact driver may not have enough torque to break loose a lug nut that's rusted/frozen or over tightened. via

Are torque specs important?

When attaching a wheel to a vehicle, torque specifications are the amount of force recommended on the hardware to ensure proper installation. Following exact torque specifications matters for a number of reasons. Too much torque can result in overtightening, which has significant consequences. via

Do mechanics use torque wrenches?

My situation wasn't the stereotypical use—torque wrenches are far more commonly applied to tighten lug nuts. But the fact is, they're indispensable tools for mechanics because every fastener on your car—including, yes, on your liftgate glass—has a specific torque rating. via

Does Haynes manual have torque specs?

When it is necessary to specify a torque value for a particular fastener, Haynes will provide it in either foot-pounds (ft-lbs.) or inch-pounds (in-lbs.). One foot-pound of torque is equivalent to 12 inch-pounds of torque. Torque values below approximately 15 ft-lbs. via

What happens if you don't get your tires torqued?

If your lug nuts are not torqued enough, they are loose, and may continue to loosen until they fall off while driving. In either case, driving without one or more functional wheel studs can be dangerous and could result in losing a tire while driving, a situation you do not want to be in. via

How often should lug nuts be replaced?

Depending on the type of vehicle it is and the age, the lug nuts may need to be replaced anywhere between five and 15 years. The cost of lug nuts or lug bolts can range from $2 to $7 or $8 a piece on most vehicles. via

Do you need to re torque aluminum wheels?

(CBC) Muise said they recommend re-torquing wheels after driving 100 kilometres after a change. He said only about 30 to 40 per cent of drivers do come back. It's even more important with aluminum rims, he added, which are softer than steel, as the lug nuts can loosen more easily, meaning a higher chance of a problem. via

Do you grease wheel nuts?

Ideally you shouldn't put any grease on the threads or on the contact face with the hub - as number cruncher says this is basically a friction coupling to your wheel. Torque should go through this and not through the wheel bolts. The bolts are to provide compression, not to carry braking/acceleration forces. via

How long does it take to get wheels Retorqued?

Let's find out. You need to get your new tires retorqued. This needs to be done in either 1-2 days or driving 50-100 miles after the tire change. As the lug nuts might tighten or loosen during this duration due to typical stresses of the vehicle's weight, nudges from bumps, and rotational effects of driving. via

Do I need special lug nuts for aftermarket wheels?

Remember that nearly all aftermarket wheels require aftermarket lug nuts because the stock ones will not fit. The more you know about lug nuts, the more secure you and your wheels will be. Add lug nuts to your wheel purchase today! via

Can I drive with 4 lug nuts?

It's OK to drive with 4! You have not mentioned (or I have missed it) if it was on front or rear wheel. There is less stress on rear wheels as they always rotate straight and obviously more stress on front wheels, when you turn - there are always several additional forces on front wheels! via

Are lug nuts SAE or metric?

You can get the lug nut's thread size by measuring the diameter of the stud it matches. Since these measurements tend to be of small circular surfaces and need to be precise, dial or digital calipers are the best tools for the job. Your vehicle may use SAE or metric: Common SAE sizes are 7/16, 1/2, 9/16 and 5/8. via

What size are the lug nuts on a 2007 Subaru Outback?

Subaru Outback 2007, Chrome Cone Seat Bulge Open End Lug Nut by Dorman®. Thread Size: M12 x 1.25. Hex Size: 19 mm. Overall Length: 1.204". via

What size are Subaru Impreza lug nuts?

M12x1. 25 Bulge Acorn Locking Wheel Lug Nuts (3/4" and 13/16" Hex) via

What size lug nuts are on a 2017 Subaru Outback?

Subaru Outback 2017, Cone Seat Acorn Lug Nuts by Gorilla Automotive®. Thread Size: M12 x 1.25. Hex Size: 13/16". Overall Length: 35.56 mm. via

Leave a Reply

Your email address will not be published.