What jeeps have Dana 35 axles?

The most common Dana 35 applications are as a rear axle in the Jeep Cherokee, Jeep Wrangler, and Jeep Comanche and as a front axle in the Ford Explorer and Ford Ranger. It is "reliable in day-to-day street use, but notoriously the opposite when worked hard." via

Can Dana 35 Handle 35 tires?

And the front axle never sees more than about 50 percent of the stress that the rear axle does. 35" tires are not recommended on a dana 35. via

How do I identify a Dana 35 axle?

There are a few things that can help you tell if the axle is a Dana 35 or a Dana 44. The easiest way to tell these axles apart is to look at the shape of the differential cover. The Dana 35 cover is pretty much perfectly round. The Dana 44 is sort of a six-sided shape. via

What gearing is a Dana 35?

Dana 35 3.08-5.13 Ratio. via

What's the difference between a Dana 35 and 44?

The Dana 44 and Dana 35 have been used in many vehicles, but there are clear distinctions between them. The Dana 35 is better used as an all-purpose axle, while the Dana 44 and its 8.5-inch ring gear are great for off-roading. For identification purposes, the shape of the differential cover is a dead giveaway. via

How can you tell the difference between a Dana 30 and a Dana 35?

The Dana 30 will only be found as a Jeep front axle while the Dana 35 will only be found as a rear axle on Wranglers. Dana 35 axles have earned a very poor reputation in the off-roading world, however, it is a great axle for stock Wranglers. via

Which Dana axle do I have?

Stamped Number on the Axle

To figure out exactly what axle you have, you can look for the Dana stamped bill of materials number. This stamped number can usually be found on the righthand side or on the longer axletube on the same side of the tube as the differential cover, facing the rear of the truck. via

How do you find out what differential I have?

Differential Identification using Tags & Stampings

The most accurate differential identification is provided by the bottom line of the tag number or axle tube stamp. Differential tags can easily be used to identify Dana and Ford differentials. via

Does a Dana 35 have C clips?

The '90-and-later Dana 35s have C-clips that retain the axles in the housing. If a C-clip shaft snaps, the axle, wheel, and brake drum will liberate themselves from the housing if you try to drive on it. via

How do you rebuild a Dana 35 rear end? (video)

https://www.youtube.com/watch?v=rmrA78goJpE

What cars have a Ford 8.8 rear end?

Common Applications

  • 1986-2014 Ford Mustang.
  • 1982-2012 Ford F-150.
  • 1982-1996 Ford Bronco.
  • 2001-2005 Ford Explorer Sport Trac.
  • 1991-2011 Ford Ranger 4.0L models.
  • 1991-2001 Ford Explorer (Solid axle)
  • 1985-2011 Ford Panther platform vehicles.
  • 2012–Present Ford F-150 (Super 8.8, depending on engine and other options)
  • via

    Are Dana and Spicer the same?

    Spicer® is a Dana brand name—it's the brand name Dana uses for their axle and driveshaft products. via

    Do Jeep Wranglers have limited slip differential?

    Jeep limited slip differentials combine the benefits of an open and a locked differential. They are less common on Wranglers than open differentials. A limited slip differential was a factory option and is also sold as an aftermarket upgrade. via

    Is Dana 30 or 35 better?

    On a dana 35 the housing its self is very weak and flexable,So when it breaks your super screwed and can't do any trail/road side repairs on it. A dana 30 is a front axle which will always take less abuse then a rear axle. And the dana 30 is made pretty beefy factory for its size. via

    What is a Dana 30a?

    < Jeep Liberty. The 27 spline Dana 30a, also know by Chrysler as the 186FIA, has always been the only front axle available in the Jeep Liberty. It's an IFS axle with an aluminum housing as indicated by the 'FI' and 'A'/'a' respectively. Essentially, it's an aluminum version of the Dana 30 with a longer pinion shaft. via

    How do you read axle tags? (video)

    https://www.youtube.com/watch?v=90o5QtER-FI

    How do I know what gear ratio My rear end is?

    Turn the wheel TWO revolutions and count the number of driveshaft turns. The number of driveshaft rotations will help you determine your rear axle ratio. For example, if it turned 3 and a half times, it's a 3.50:1 ratio. If it turned 4 and a quarter times, it's a 4.25:1 ratio. via

    What do differential numbers mean?

    The term refers to the gears in the truck's differential, which is a mechanical device that links the rear axle to the driveshaft and then the engine. Technically, the number should be expressed as a ratio, such as 3.55:1, meaning the drive shaft turns 3.55 times for each turn of a wheel. via

    What spline is a Dana 35?

    Dana 35 Right Chromoly Axle Shaft (30 Spline) via

    How much oil does a Dana 35 take?

    1.8 Quarts

    Jeep Wrangler JL Differential Fluid Capacity
    Axle: 186 - Front Axle Non Rubicon Capacity: 1.82 Pints
    Axle: Dana 30 Axle Capacity: 1.3 Quarts / 1.2 Liters
    Axle: Dana 35 Axle Capacity: 1.8 Quarts / 1.7 Liters
    Axle: Dana 44 Axle Capacity: 2.0 Quarts / 1.9 Liters

    via

    How much stronger are chromoly axles?

    1541H can be 50 percent stronger than OE 1040 and about 12 percent stouter than 1050. 4140: 41xx designates the chromoly group. Chromium offers three benefits: improved hardness, better elasticity during quenching, and greater corrosion resistance. Molybdenum and nickel further increase hardness. via

    How hard is it to rebuild a rear differential?

    A complete rear differential replacement includes replacing the housing, gears, bearings, and seals. The average time it takes a certified mechanic to perform a differential rebuild at a shop is usually three to five hours. A rebuild on a commercial vehicle by someone without prior experience could take much longer. via

    How do you remove an axle shaft on a Dana 35? (video)

    https://www.youtube.com/watch?v=HjIyyFf1iBo

    How do you change a pinion bearing? (video)

    https://www.youtube.com/watch?v=7yBPe7-bwBs

    What is a Dana 40?

    There is no dana 40. You're thinking of the Dana 44. It's a medium duty axle that has been used as both a front and rear axle over the years. As a front axle, it was used in 1/2 and 3/4 ton pickup trucks made by every domestic truck manufacturer at one time or another. via

    Is Dana and Eaton the same company?

    Eaton completes purchase of Dana Corp. division - Milwaukee Business Journal. via

    Is Dana an OEM?

    As an OEM manufacturer, Dana can deliver replacement gaskets and sets manufactured to the highest quality standards and specifications. With an extensive product portfolio, we ensure wide product availability backed by technical service support throughout the world. via

    Leave a Reply

    Your email address will not be published.